ABS filament for heat-resistant parts
Part of the heat-resistant filament guide. ABS is a common step up from PLA and PETG for parts that sit in warm places, such as automotive interior trim and clips or housings near motors and electronics. It needs a heated bed and, per Bambu, an enclosed printer. Nothing here was printed or measured by this site; every value links to its source.
What Bambu says about printing it
| Category | In Bambu's table? | Bambu Lab A1 mini | Bambu Lab A1 | Bambu Lab P1S | Bambu Lab X1 Carbon (X1C) | AMS | AMS lite |
|---|---|---|---|---|---|---|---|
| ABS | Yes | Not Recommended | Not Recommended | Recommended | Recommended | Compatible | Not Recommended |
| ABS-GF | Yes | Not Recommended | Not Recommended | Recommended | Recommended | Compatible | Not Recommended |
| ABS-CF | No (derived, see note) | Not rated (Bambu recommends an enclosed printer) | Not rated (Bambu recommends an enclosed printer) | Recommended (Bambu printer-requirements table) | Recommended (Bambu printer-requirements table) | Not rated by Bambu | Not rated by Bambu |
- ABS-CF: Not a row in Bambu's compatibility table. Bambu's printer-requirements table groups ABS, ASA, PC, PA "and their CF/GF reinforced materials" under enclosed printers, and its nozzle guidance requires a hardened steel nozzle for CF/GF materials. (source)
| Material group | Hardened steel nozzle | Nozzle temp (°C) | Bed temp (°C) | Drying before use |
|---|---|---|---|---|
| ABS | Not required | 240–280 | 90–100 | Recommended: 80 °C for 8 h (oven) |
Heat-resistance values from manufacturer datasheets
Sorted by HDT at 0.45 MPa. A dash means the datasheet does not give that value (or gives it without a stated load), so it is left blank rather than estimated. HDT is a lab comparison value measured on test bars under a fixed load, not a rated service temperature, and depends on test method, print orientation and annealing. Retrieved .
| Brand | Product | HDT 0.45 MPa (°C) | HDT 1.8 MPa (°C) | Tg (°C) | Vicat (°C) | HDT method | Notes | Source |
|---|---|---|---|---|---|---|---|---|
| Polymaker | PolyLite ABS | 100 | 98 | 101 | 104 | ISO 75 | — | TDS |
| Bambu Lab | ABS-GF | 99 | 88 | — | 103 | ISO 75 | TDS: specimens annealed and dried at 80 °C for 12 h before testing. TDS lists Tg as N/A. | TDS |
| Sunlu | ABS | 95 | — | 109 | 86 | ISO 75 (X-Y) | TDS gives ±5 °C on HDT; no 1.8 MPa value. | TDS |
| Sunlu | High Speed ABS | 93 | — | 105 | 80 | ISO 75 (X-Y) | No 1.8 MPa value. | TDS |
| Sunlu | ABS-FR | 90.5 | — | — | — | ISO 75 (X-Y) | TDS gives ±3 °C; Tg and Vicat listed as "/". | TDS |
| Bambu Lab | ABS | 87 | 84 | — | 94 | ISO 75 | TDS: specimens annealed and dried at 80 °C for 12 h before testing. TDS lists Tg as N/A. | TDS |
| Extrudr | DuraPro ABS | — | — | — | 92 | — | TDS gives "HDT/B ASTM D648 85 °C" without stating the load, so it is not assigned to a load column here. | TDS |
| Overture | ABS | — | — | — | 103.4 | — | TDS lists Vicat only; no HDT or Tg. | TDS |
ABS products in the database
Products with enough sourced data for a page, datasheet heat values first. Enclosure and nozzle columns come from the product's Bambu category plus the database's abrasive and fibre tags; open a product page for the basis of each.
| Product | Brand | Category | Enclosure | Hardened nozzle | HDT 0.45 MPa (°C) | Nozzle °C (min–max) |
|---|---|---|---|---|---|---|
| Bambu Lab ABS | Bambu Lab | ABS | Enclosure recommended | Not required | 87 | 240–270 |
| Bambu Lab ABS-GF | Bambu Lab | ABS-GF | Enclosure recommended | Required | 99 | 240–280 |
| extrudr DuraPro ABS | extrudr | ABS | Enclosure recommended | Not required | — | 230–260 |
| Overture ABS | Overture | ABS | Enclosure recommended | Not required | — | 245–265 |
| Polymaker Polylite ABS | Polymaker | ABS | Enclosure recommended | Not required | 100 | 245–265 |
| SUNLU ABS | SUNLU | ABS | Enclosure recommended | Not required | 95 | 250–290 |
| SUNLU ABS-FR | SUNLU | ABS | Enclosure recommended | Not required | 90.5 | 240–260 |
| SUNLU High Speed ABS | SUNLU | ABS | Enclosure recommended | Not required | 93 | 260–290 |
| SUNLU PC-ABS | SUNLU | ABS | Enclosure recommended | Not required | 102 | 260–280 |
| 3D Fuel Pro ABS | 3D Fuel | ABS | Enclosure recommended | Required | — | 230–260 |
| 3DE Pirate Black | 3DE | ABS | Enclosure recommended | Not required | — | 240–270 |
| 3DJAKE ABS | 3DJAKE | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DPower ABS | 3DPower | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXMax | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXStat ESD | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS 3DXTech | 3DXTech | ABS | Enclosure recommended | Not required | — | 230–260 |
| 3DXTech ABS CF | 3DXTech | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| 3DXTech ABS GF | 3DXTech | ABS-GF | Enclosure recommended | Required | — | 230–260 |
| Add-North ABS | Add-North | ABS | Enclosure recommended | Not required | — | 230–260 |
| Add-North rABS | Add-North | ABS | Enclosure recommended | Not required | — | ––– |
| Ambrosia ABS Matte | Ambrosia | ABS | Enclosure recommended | Not required | — | 230–265 |
| Ambrosia Über ABS | Ambrosia | ABS | Enclosure recommended | Not required | — | 225–250 |
| Anycubic ABS | Anycubic | ABS | Enclosure recommended | Not required | — | 240–280 |
| Atomic Filament ABS | Atomic Filament | ABS | Enclosure recommended | Not required | — | 230–260 |
| Atomic Filament ABS CF | Atomic Filament | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| AURAPOL ABS | AURAPOL | ABS | Enclosure recommended | Not required | — | 230–260 |
| AzureFilm ABS Plus | AzureFilm | ABS | Enclosure recommended | Not required | — | 250–250 |
| AzureFilm ABS Prime | AzureFilm | ABS | Enclosure recommended | Not required | — | 250–250 |
| Buddy3D ABS | Buddy3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Buddy3D Matte ABS | Buddy3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| CC3D ABS | CC3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| COEX 3D ABS | COEX 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Cookiecad ABS | Cookiecad | ABS | Enclosure recommended | Not required | — | 230–260 |
| Creality ABS | Creality | ABS | Enclosure recommended | Not required | — | 230–260 |
| Creality Hyper ABS | Creality | ABS | Enclosure recommended | Not required | — | ––– |
| Devil Design ABS | Devil Design | ABS | Enclosure recommended | Not required | — | 230–260 |
| ELEGOO ABS | ELEGOO | ABS | Enclosure recommended | Not required | — | 240–280 |
| Eolas Prints ABS | Eolas Prints | ABS | Enclosure recommended | Not required | — | 230–260 |
| Eryone ABS | Eryone | ABS | Enclosure recommended | Not required | — | 230–270 |
| Eryone ABS High-Speed | Eryone | ABS | Enclosure recommended | Not required | — | 240–290 |
| Eryone ABS-CF | Eryone | ABS-CF | Enclosure recommended | Required | — | 240–280 |
| Eryone ABS-GF | Eryone | ABS-GF | Enclosure recommended | Required | — | 240–280 |
| Eryone ABS-PC | Eryone | ABS | Enclosure recommended | Not required | — | 240–260 |
| Eryone ABS+ | Eryone | ABS | Enclosure recommended | Not required | — | 230–260 |
| eSUN 3D ABS+ | eSUN 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| eSUN 3D ABS+CF | eSUN 3D | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| eSUN 3D ABS+HS | eSUN 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Fiberlogy ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 230–260 |
| Fiberlogy R ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| Fiberlogy Refill ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| Fiberlogy Refill R ABS | Fiberlogy | ABS | Enclosure recommended | Not required | — | 250–265 |
| FilamentPM ABS | FilamentPM | ABS | Enclosure recommended | Not required | — | 230–260 |
| Filamentworld ABS | Filamentworld | ABS | Enclosure recommended | Not required | — | 230–260 |
| Filatech ABS | Filatech | ABS | Enclosure recommended | Not required | — | 230–260 |
| FLASHFORGE ABS | FLASHFORGE | ABS | Enclosure recommended | Not required | — | 230–260 |
| FLASHFORGE D Series ABS | FLASHFORGE | ABS | Enclosure recommended | Not required | — | 230–260 |
| FormFutura ABSpro | FormFutura | ABS | Enclosure recommended | Not required | — | 230–255 |
| FormFutura ABSpro Flame Retardant | FormFutura | ABS | Enclosure recommended | Not required | — | 240–265 |
| FormFutura EasyFil ABS | FormFutura | ABS | Enclosure recommended | Not required | — | 230–260 |
| FormFutura EasyFil ABS - Glow in the Dark | FormFutura | ABS | Enclosure recommended | Required | — | 230–255 |
| FormFutura Premium ABS Medical | FormFutura | ABS | Enclosure recommended | Not required | — | 235–260 |
| FormFutura ReForm - rTitan | FormFutura | ABS | Enclosure recommended | Not required | — | 245–265 |
| FormFutura TitanX | FormFutura | ABS | Enclosure recommended | Not required | — | 245–270 |
| Francofil ABS | Francofil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Geeetech ABS+ | Geeetech | ABS | Enclosure recommended | Not required | — | 220–250 |
| Geeetech Upgrade ABS | Geeetech | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks ABS CF | Gizmo Dorks | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Gizmo Dorks Color Change ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Fluorescent ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Glow ABS | Gizmo Dorks | ABS | Enclosure recommended | Required | — | 230–260 |
| Gizmo Dorks Low Odor ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| Gizmo Dorks Thermochromic ABS | Gizmo Dorks | ABS | Enclosure recommended | Not required | — | 230–260 |
| GST3D ABS | GST3D | ABS | Enclosure recommended | Not required | — | ––– |
| Hatchbox ABS | Hatchbox | ABS | Enclosure recommended | Not required | — | 210–240 |
| Hatchbox Glow ABS | Hatchbox | ABS | Enclosure recommended | Required | — | 210–240 |
| IC3D ABS | IC3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| IEMAI ABS | IEMAI | ABS | Enclosure recommended | Not required | — | 220–260 |
| IEMAI CF-ABS | IEMAI | ABS-CF | Enclosure recommended | Required | — | 220–260 |
| IEMAI ESD-ABS | IEMAI | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inland ABS | Inland | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inland Glow ABS | Inland | ABS | Enclosure recommended | Required | — | 230–260 |
| Inslogic ABS FR V0 | Inslogic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Inslogic ABS GF10 | Inslogic | ABS-GF | Enclosure recommended | Required | — | 240–270 |
| kexcelled The K5 ABS T | kexcelled | ABS | Enclosure recommended | Not required | — | 250–290 |
| Kingroon ABS | Kingroon | ABS | Enclosure recommended | Not required | — | 230–260 |
| LDO ABS | LDO | ABS | Enclosure recommended | Not required | — | 250–270 |
| MatterHackers ABS | MatterHackers | ABS | Enclosure recommended | Not required | — | 230–260 |
| Mosaic ABS | Mosaic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Glowing | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Marble Gray | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Art Thermo | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nebula ABS Tech 702 | Nebula | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil Glow ABS | Nobufil | ABS | Enclosure recommended | Required | — | 230–260 |
| Nobufil X Astro ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Candy ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Industrial ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Matt Matte ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Nobufil X Neon ABS | Nobufil | ABS | Enclosure recommended | Not required | — | 230–260 |
| Overture Glow ABS | Overture | ABS | Enclosure recommended | Required | — | 245–265 |
| Paramount 3D ABS | Paramount 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Paramount 3D ABS CF | Paramount 3D | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| PolyLite ABS | PolyLite | ABS | Enclosure recommended | Not required | — | 245–265 |
| Polymaker Metallic Polylite Silk ABS | Polymaker | ABS | Enclosure recommended | Not required | — | 230–260 |
| PrimaCreator Primaselect ABS | PrimaCreator | ABS | Enclosure recommended | Not required | — | 220–250 |
| PrimaCreator Primaselect Glow ABS | PrimaCreator | ABS | Enclosure recommended | Required | — | 230–260 |
| PrimaCreator Primavalue ABS | PrimaCreator | ABS | Enclosure recommended | Not required | — | 240–270 |
| PrimaSelect ABS | PrimaSelect | ABS | Enclosure recommended | Not required | — | 220–250 |
| PrimaValue ABS | PrimaValue | ABS | Enclosure recommended | Not required | — | 240–270 |
| Print With Smile ABS | Print With Smile | ABS | Enclosure recommended | Not required | — | 230–260 |
| PrintedSolid ABS CF | PrintedSolid | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Push Plastic ABS | Push Plastic | ABS | Enclosure recommended | Not required | — | 230–260 |
| Push Plastic CF ABS | Push Plastic | ABS-CF | Enclosure recommended | Required | — | 230–260 |
| Push Plastic Matte ABS | Push Plastic | ABS | Enclosure recommended | Not required | — | 230–260 |
| QIDI Tech ABS Metal Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 220–250 |
| QIDI Tech ABS Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 240–280 |
| QIDI Tech ABS-GF25 | QIDI Tech | ABS-GF | Enclosure recommended | Required | — | 240–280 |
| QIDI Tech Odorless ABS Rapido | QIDI Tech | ABS | Enclosure recommended | Not required | — | 240–280 |
| ROSA3D Filaments ABS V0 FR | ROSA3D Filaments | ABS | Enclosure recommended | Not required | — | 230–260 |
| ROSA3D Filaments Matte ABS | ROSA3D Filaments | ABS | Enclosure recommended | Not required | — | 230–260 |
| RS PRO ABS | RS PRO | ABS | Enclosure recommended | Not required | — | 230–270 |
| SainSmart ABS | SainSmart | ABS | Enclosure recommended | Not required | — | 230–260 |
| Sakata 3D ABS | Sakata 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Siraya Tech Fibreheart ABS HT HF | Siraya Tech | ABS | Enclosure recommended | Not required | — | 240–260 |
| Siraya Tech Fibreheart ABS-CF Core | Siraya Tech | ABS-CF | Enclosure recommended | Required | — | 250–280 |
| Siraya Tech Fibreheart ABS-GF | Siraya Tech | ABS-GF | Enclosure recommended | Required | — | 250–270 |
| SMART MATERIALS 3D ABS | SMART MATERIALS 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Snapmaker ABS | Snapmaker | ABS | Enclosure recommended | Not required | — | 240–280 |
| SOVB 3D Fil ABS | SOVB 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| SOVB 3D Glow ABS | SOVB 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| Spectrum ABS | Spectrum | ABS | Enclosure recommended | Not required | — | 230–260 |
| Spectrum ABS FR V0 | Spectrum | ABS | Enclosure recommended | Not required | — | 240–265 |
| Spectrum ABS GP450 | Spectrum | ABS | Enclosure recommended | Not required | — | 235–255 |
| Spectrum ABS Kevlar | Spectrum | ABS | Enclosure recommended | Required | — | 250–270 |
| Spectrum ABS Medical | Spectrum | ABS | Enclosure recommended | Not required | — | 235–255 |
| Spectrum smart ABS | Spectrum | ABS | Enclosure recommended | Not required | — | 230–255 |
| Tectonic 3D Aura ABS | Tectonic 3D | ABS | Enclosure recommended | Not required | — | 230–260 |
| TEQStone ABS | TEQStone | ABS | Enclosure recommended | Not required | — | 210–250 |
| TINMORRY ABS Pro | TINMORRY | ABS | Enclosure recommended | Not required | — | 220–260 |
| Verbatim ABS | Verbatim | ABS | Enclosure recommended | Not required | — | 230–260 |
| Winkle ABS | Winkle | ABS | Enclosure recommended | Not required | — | 230–260 |
More
- All ABS filaments (full spec tables)
- ASA filament for heat-resistant and outdoor parts
- Polycarbonate (PC) filament for heat-resistant parts
- Nylon (PA6, PA12) filament for heat-resistant parts
- Carbon-fiber-filled filament for heat-resistant parts
Affiliate disclosure: once this site is live, some links like the ones below may be affiliate links, meaning we could earn a commission if you buy through them, at no extra cost to you. That would not change which data we show. In this prototype, no affiliate program has been joined and these are placeholder links.